Linux Wireless

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

Go back --> [[en/users/Drivers/ath10k|ath10k]] 

 


===== ath10k spectral scan: =====

Atheros 802.11ac chipsets include a built-in spectral analysis feature. They have the ability to report FFT data from the baseband under software controlled conditions. 

These information can be used to create an open source spectrum analyzer or interference classifier 

To try it out, you can use the following commands while having an open connection (e.g. running an AP) to acquire samples for the current channel: 


<code>    ip link set dev wlan0 up
    echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
    echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
    iw dev wlan0 scan
    echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
    cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples</code>
    
Spectral scan configuration parameters can be read and changed /sys/kernel/debug/ieee80211/phy0/ath10k/: 
  * spectral_count: number of scan results requested. Note that the "never disable" mode is implemented through the "background" mode in specral_scan_ctl, see below. Note that the count number may be ignored for 20 MHz and 40 MHz for unknown reasons (see open issues below) 
  * spectral_bins: contains the number of bins returned in one fft sample. Allowed values are 64, 128, and 256. Configuring more bins will allow higher resolutions in the fft data. Note that configuring 64 bins will not work with 80 MHz wide channels (the hardware reports samples which appear to be bogus and are not returned to userspace). 
  * spectral_scan_ctl: Contains the current mode. There are the following modes available: 
     * disable: spectral scan is disabled 
     * background: spectral scans samples are returned endlessly from the currently configured channel. It is running while the hardware is not busy with sending/receiving. Must be turned on by writing "trigger" into spectral_scan_ctl. 
     * manual: as many spectral scan samples as configured in spectral_count are returned from the current channel after writing "trigger" into spectral_scan_ctl. 
  *   spectral_scan0: the relayfs file which returns the spectral scan samples. The samples are returned as TLV binary data, see drivers/net/wireless/ath/spectral_common.h for the format 

===== Open issues =====


==== The spectral count issue ====

Even when a count is specified, the hardware seems to send endless samples. It seems to work most of the time in VHT80 mode though, but in HT20 and HT40 the count value seems to be ignored. To reproduce this, start hostapd with the desired channel width and do: 

<code>
echo 8 > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count
echo manual > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 >> /tmp/fft.dump</code>

Repeating the last line and checking the filesize will easily show whether ath10k still sends samples or not. We would expect 8 samples in this configuration. 


===== Userspace programs: =====

FFT samples gathered from Atheros NICs could be drawn using userspace programs: 
  * [[https://github.com/simonwunderlich/FFT_eval|https://github.com/simonwunderlich/FFT_eval]]
Linux Wireless

User Tools

Site Tools

Page Tools
