en:developers:documentation:cfg80211
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
en:developers:documentation:cfg80211 [2015/05/26 14:01] Johannes Berg fix link |
en:developers:documentation:cfg80211 [2015/05/26 14:03] (current) Johannes Berg |
||
|---|---|---|---|
| Line 13: | Line 13: | ||
| We now have a few cfg80211 drivers, a good example of a full cfg80211 drivers is the Atheros ath6kl driver. Instead of writing wext ioctls you now write cfg80211 operation callbacks and fill in the wiphy struct to indicate to cfg80211 its device capabilities. | We now have a few cfg80211 drivers, a good example of a full cfg80211 drivers is the Atheros ath6kl driver. Instead of writing wext ioctls you now write cfg80211 operation callbacks and fill in the wiphy struct to indicate to cfg80211 its device capabilities. | ||
| - | As an example here is ath6kl's cfg80211_ops: | + | Then you allocate the wiphy by specifying the cfg80211 ops and fill the wiphy. For more details refer to cfg80211.h and as an example driver you can read ath6kl (or any other cfg80211-only driver, or even mac80211.) There's a [[api-list|list of APIs per interface mode]]. |
| - | + | ||
| - | + | ||
| - | <code>static struct cfg80211_ops ath6kl_cfg80211_ops = { | + | |
| - | .add_virtual_intf = ath6kl_cfg80211_add_iface, | + | |
| - | .del_virtual_intf = ath6kl_cfg80211_del_iface, | + | |
| - | .change_virtual_intf = ath6kl_cfg80211_change_iface, | + | |
| - | .scan = ath6kl_cfg80211_scan, | + | |
| - | .connect = ath6kl_cfg80211_connect, | + | |
| - | .disconnect = ath6kl_cfg80211_disconnect, | + | |
| - | .add_key = ath6kl_cfg80211_add_key, | + | |
| - | .get_key = ath6kl_cfg80211_get_key, | + | |
| - | .del_key = ath6kl_cfg80211_del_key, | + | |
| - | .set_default_key = ath6kl_cfg80211_set_default_key, | + | |
| - | .set_wiphy_params = ath6kl_cfg80211_set_wiphy_params, | + | |
| - | .set_tx_power = ath6kl_cfg80211_set_txpower, | + | |
| - | .get_tx_power = ath6kl_cfg80211_get_txpower, | + | |
| - | .set_power_mgmt = ath6kl_cfg80211_set_power_mgmt, | + | |
| - | .join_ibss = ath6kl_cfg80211_join_ibss, | + | |
| - | .leave_ibss = ath6kl_cfg80211_leave_ibss, | + | |
| - | .get_station = ath6kl_get_station, | + | |
| - | .set_pmksa = ath6kl_set_pmksa, | + | |
| - | .del_pmksa = ath6kl_del_pmksa, | + | |
| - | .flush_pmksa = ath6kl_flush_pmksa, | + | |
| - | CFG80211_TESTMODE_CMD(ath6kl_tm_cmd) | + | |
| - | #ifdef CONFIG_PM | + | |
| - | .suspend = __ath6kl_cfg80211_suspend, | + | |
| - | .resume = __ath6kl_cfg80211_resume, | + | |
| - | #endif | + | |
| - | .start_ap = ath6kl_start_ap, | + | |
| - | .change_beacon = ath6kl_change_beacon, | + | |
| - | .stop_ap = ath6kl_stop_ap, | + | |
| - | .del_station = ath6kl_del_station, | + | |
| - | .change_station = ath6kl_change_station, | + | |
| - | .remain_on_channel = ath6kl_remain_on_channel, | + | |
| - | .cancel_remain_on_channel = ath6kl_cancel_remain_on_channel, | + | |
| - | .mgmt_tx = ath6kl_mgmt_tx, | + | |
| - | .mgmt_frame_register = ath6kl_mgmt_frame_register, | + | |
| - | .sched_scan_start = ath6kl_cfg80211_sscan_start, | + | |
| - | .sched_scan_stop = ath6kl_cfg80211_sscan_stop, | + | |
| - | };</code> | + | |
| - | Then you allocate the wiphy by specifying the cfg80211 ops and fill the wiphy. | + | |
| - | + | ||
| - | For more details refer to cfg80211.h and as an example driver you can read ath6kl. | + | |
| ===== Regulatory ===== | ===== Regulatory ===== | ||
en/developers/documentation/cfg80211.txt · Last modified: 2015/05/26 14:03 by Johannes Berg
Page Tools
